Enerdrive 40A AC and DC DIY Installation Kit, With Simarine Battery Monitor & 2000W RCD & AC Transfer Switch Inverter (K-AGM-Board-F)
SKU: K-AGM-Board-F Learn More»
Enerdrive 40A AC and DC DIY Installation Kit, With Simarine Battery Monitor & 2000W RCD & AC Transfer Switch Inverter (K-AGM-Board-F)
Introducing Enerdrives DIY Installation Kits for 4WD Canopies, Caravans, Camper Trailers, Commercial Work Vehicles and more. Enerdrive have created many different layouts and dimensional sizes to fit nearly every possible application. Designed for the DIY handyman with basic electrical knowledge through to the professional looking to save installation time. From small kits with AC & DC charging and battery monitoring up to kits with 2000w inverters and individual charge/load monitoring.
These kits are all pre-wired by Enerdrive where possible to keep the kits simple to install. All boards have a full wiring diagram showing each circuit and where to connect your loads, battery and inverter cabling. All items are mounted on a 12mm Black plastic (water & rot resistant) board for simple mounting into the application.
Shipping Note: This item comes on a pallet. The freight charge is for delivery to commercial premises with unloading facilities or the nearest freight depot. If you require delivery to a residential address, you will need to call us before ordering so we can book in a tail gate service (which will incur an extra $150 surcharge).
Includes:
- Enerdrive ePOWER 12V 40A DC to DC Battery Charger EN3DC40+
- Enerdrive ePOWER 12V 40A Battery Charger EN31240
- Simarine Pico LCD WIFI Monitoring Screen
- Simarine SC301 300A Main Battery Shunt
- Simarine SCQ25T Individual Load/Charge Module
- 3 Stud Main Negative Bus Bar
- 40A Low Battery Cutout
- Main System Circuit Breaker 120A
- Inverter Circuit Breaker 200A
- Solar Input Positive Circuit Breaker 40A
- ePOWER DC2DC 60A Output Fuse Connection
- ePOWER AC Charger 50A Output Fuse Connection
- 2 x 30A Load Output Fuse Connections
- 24hr Critical Load 4 Circuit "Wedge" Fuse Block
- ePOWER 2000W AC Transfer Inverter
- Battery Restart Switch (Lithium Batteries)
- 12mm Black Plastic Mounting Board. Water & Rot Resistance
EXPERT TIP: One or two AGM Board Cable Kits are common accessories suitable for the Enerdrive K-AGM-Board-F. Thickness, length and quantity will depend on installation type. Please check cable description for details. All the accessories are available in the Accessory List above as optional extras.
Items Included | K-AGM-Board-C | K-AGM-Board-D | K-AGM-Board-E | K-AGM-Board-F | K-AGM-Board-G | K-DIY-Board-01 |
ePOWER AC 40Amp 230v Charger | * | * | * | * | * | * |
ePOWER DC2DC 40+ Charger (Vehicle/Solar) | * | * | * | * | * | * |
ePRO Plus 500A Battery Monitor with Remote Display | * | * | * | |||
Simarine Pico LCD WIFI Monitoring Screen | * | * | * | |||
Simarine SC301 300A Main Battery Shunt | * | * | * | |||
Simarine SCQ25T Individual Load/Charge Module | * | * | * | |||
3 Stud Main Negative Bus Bar | * | * | * | * | * | * |
40A Low Battery Cutout | * | * | * | * | * | * |
Main System Circuit Breaker 120A | * | * | * | * | * | * |
Inverter Circuit Breaker 200A | * | * | * | * | * | * |
Solar Input Positive Circuit Breaker 40A | * | * | * | * | ||
ePOWER DC2DC 60A Output Fuse Connection | * | * | * | * | * | * |
ePOWER AC Charger 50A Output Fuse Connection | * | * | * | * | * | * |
1 x 30A Load Output Fuse Connections | * | |||||
2 x 30A Load Output Fuse Connections | * | * | ||||
50A Load Output Fuse Connection | * | |||||
24hr Critical Load 4 Circuit "Wedge" Fuse Block | * | * | * | |||
24hr Critical Load 8 Circuit "Wedge" Fuse Block | * | |||||
Main 6 Circuit "Wedge" Fuse Block with Negative Bus and Cover | * | |||||
Main 12 Circuit "Wedge" Fuse Block with Negative Bus and Cover | * | * | ||||
ePOWER 2000W AC Transfer Inverter | * | * | ||||
Battery Restart Switch (Lithium Batteries) | * | * | * | * | * | |
12mm Black Plastic Mounting Board. Water & Rot Resistance | * | * | * | * | * | * |
175A Anderson Plug (Inverter) | * | |||||
50A Anderson Plug (Solar Input) | * | |||||
50A Anderson Plug (Vehicle Input) | * | |||||
Dimensions (L x W x D) | 1185 x 380 x 130 mm | 600 x 490 x 100 mm | 600 x 490 x 100 mm | 1185 x 380 x 130 mm | 790 x 380 x 100 mm | 580 x 580 x 100 mm |
Weight | 23 kg | 14 kg | 14 kg | 23 kg | 16 kg | 14 kg |
(*) Indicates Standard Fitment |
Specifications:
Model | EN3DC40+ (DC Battery Charger) | EN31240 (AC Battery Charger) | SI-PICO-3 (Battery Monitor) | EN1120S (Inverter) |
---|---|
Charger Mode Output Voltage | 13.8V - 15.5V (DC Battery Charger) | 14.2 – 15.5 V (AC Battery Charger) |
Float | 13.0V - 13.8V (DC Battery Charger) | 13.4 – 13.8 V (AC Battery Charger) |
Equalize | 15.5V (DC Battery Charger) | 16.0 V (AC Battery Charger) |
Amps | 40A (DC & AC Battery Charger) |
Charging Control | Four stages (Bulk/Absorption/Float/Maintenance), Two stages (Bulk/Absorption)Constant Power Supply (Program setting), Priority Battery Bank Charging (AC Battery Charger) |
DC Output | Single (DC Battery Charger) | Three (1 fully independent, 2 common with diode isolation) (AC Battery Charger) |
Operating Voltage | 6 - 35V (Battery Monitor) |
Selectable Battery Type | Gel, AGM, Flooded, Lithium, Program (DC and AC Battery Charger) |
Standby Current | < 2 mA (AC Battery Charger) |
AC Input Voltage | 90 to 265 VAC (AC Battery Charger) |
AC Input Operating Range | 207-265 Vac (3.8 A Max) 90 – 125 Vac (7.7 A Max) (AC Battery Charger) |
AC Input Frequency Range | 47 – 63 Hz (AC Battery Charger) |
Power consumption (DC 12V) | 700W (Full Load) (AC Battery Charger) |
Power Factor Correction | Yes (AC Battery Charger) |
Charger Efficiency | 95% (DC Battery Charger) | > 82% (AC Battery Charger) |
Reverse Polarity | Yes, (with user replaceable fuse/s) (AC Battery Charger) |
Over Charge | Yes, unit shutdown (AC Battery Charger) |
Over Temperature Protection | Yes, unit de-rated and shutdown (AC Battery Charger) |
Cooling | Forced air ventilation (thermo controlled fan) (AC Battery Charger) |
Output Short Circuit | Yes, (with user replaceable fuse/s) (AC Battery Charger) |
Temperature Setting | Low/ Normal/ High (Battery Temperature Sensor Standard) (DC Battery Charger) | Hot, Normal, Cold (no sensor connected) (AC Battery Charger) |
Battery Temp Sensor Port | RJ12 (standard battery temp. sensor supplied) (AC Battery Charger) |
LCD Display | Charging status, Battery Voltage, Output Current & Fault Codes (AC Battery Charger) |
AC Input Connection | IEC with Supplied 1.2M Power Lead (AC Battery Charger) |
DC Output Connection | Heavy Duty Terminal (3 banks) – Pan Heads 6mm Thread (AC Battery Charger) |
DC Output Ground | Single Heavy Duty Common Ground Stud (AC Battery Charger) |
Storage Range (temp) | -40° to 70° C (AC Battery Charger) |
Operating Range (temp) | -20° to 60° C (AC Battery Charger) | 0°C to 40°C (Inverter) |
Humidity | 5-95%, relative humidity non-condensing (AC to DC Battery Charger) | 5-90% noncondensing (Inverter) |
Ingress Protection | IP32 (Basic drip proof in vertical orientation) (AC Battery Charger) |
Wattage (w) | 2000W (Inverter) |
Under Voltage Alarm | 11.0 / 12.1 VDC (Inverter) |
Under Voltage Alarm Recovery | 11.3 / 12.3 VDC (Inverter) |
Under Voltage Shutdown | 10.5 / 11.8 VDC (Inverter) |
Under Voltage Shutdown Recovery | 12.0 / 12.6 VDC (Inverter) |
Over Voltage Shutdown | 15.5 VDC (Inverter) |
USB Socket Output | 5V, 750 mA (Inverter) |
Regulatory Compliance | Complies with AS/NZS 60335.2.29 Including Australian deviations. |
Input Voltage | 12.5 VDC (Inverter) |
Dimensions | 1185 x 380 x 130 mm (L x W x D) |
Manufacturers Warranty | 5 Years |
Enerdrive ePOWER 12V 40A DC to DC Battery Charger:
The Enerdrive ePOWER DC2DC Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller.
Features:
- Independent DC Inputs for both engine and solar regulation charging one house battery bank output
- DC M6 screw terminals
- A dedicated Maximum Power Point (MPPT) solar regulator
- The same battery algorithms as included in our AC mains ePOWER battery charger including a specific lithium charging profile
- 40A output up to 40+°C with thermo controlled fan cooling
- Fully programmable LCD display
- Temperature sensor
SKU K-AGM-Board-F
Brand Enerdrive
Product Category Power Systems
Battery Voltage 12V
Charger Output Voltage: 13.8V - 15.5V (DC Battery Charger) | 14.2 – 15.5 V (AC Battery Charger)
Amps: 40A (DC & AC Battery Charger)
Float: 13.0V - 13.8V (DC Battery Charger) | 13.4 – 13.8 V (AC Battery Charger)
Equalize: 15.5V (DC Battery Charger) | 16.0 V (AC Battery Charger)
DC Output : Single (DC Battery Charger) | Three (1 fully independent, 2 common with diode isolation) (AC Battery Charger)
Operating Voltage: 6 - 35V (Battery Monitor)
Selectable Battery Type: Gel, AGM, Flooded, Lithium, Program (DC and AC Battery Charger)
AC Input Voltage: 90 to 265 VAC (AC Battery Charger)
AC Input Operating Range: 207-265 Vac (3.8 A Max) 90 – 125 Vac (7.7 A Max) (AC Battery Charger)
AC Input Frequency Range: 47 – 63 Hz (AC Battery Charger)
Power Consumption: 700W (Full Load) (AC Battery Charger)
Charger Efficiency: 95% (DC Battery Charger) | > 82% (AC Battery Charger)
Dimensions: 1185 x 380 x 130 mm (L x W x D)
Weight: 23 kg
Input Voltage: 12.5 VDC (Inverter)
Humidity: 5-95%, relative humidity non-condensing (AC to DC Battery Charger) | 5-90% noncondensing (Inverter)
NOTE: see full product specifications & further product info in the Description section on this page.
Warranty Period: 5 Years
Warranty Details: Please CLICK HERE for Warranty Information on this product
- We ship Australia-wide with national road express freight companies such as Star Track, TNT and Toll.
- Small Items are sent with Australia Post via regular post.
- Delivery times are generally 3-5 days from day of dispatch for major cities (sometimes quicker). Please allow longer for regional and remote areas.
- Once your item(s) have been dispatched, we will provide you freight tracking information so you can track your delivery to your door.
- Items are fully insured during the freight process.
- Unfortunately we cannot deliver to PO Boxes.
- For further details on our Delivery Process you can visit our Delivery Page HERE.
Important Covid-19 Comment: during these difficult times, our dispatch and delivery times are longer than normal. Please allow additional days for delivery over and above the normal estimates outlined above.

Be The First To Review This Product!
Help other CARAVANRVCAMPING users shop smarter by writing reviews for products you have purchased.