Victron "In Vehicle" Off Grid Charging Bundle With 30A DC to DC & 30A AC to DC Charger
Free Shipping

Victron "In Vehicle" Off Grid Charging Bundle With 30A DC to DC & 30A AC to DC Charger

SKU: BDL010 Learn More»


$1,759.00
$1,999.00
In Stock1-2 Days Dispatch

FREE SHIPPING

Learn More»

Victron "In Vehicle" Off Grid Charging Bundle With 30A DC to DC & 30A AC to DC Charger

 

Included: 

 

Victron Orion-Tr Smart 12/12-30A (360W) Non-isolated DC-DC charger:

The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth. For use in dual battery systems in vehicles or on boats where the alternator and the start battery are used to charge the service battery. This Victron battery charger can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch.

The Orion Tr-Smart Victron battery chargers can be used in 12V or 24V systems and is suitable for both lead-acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to 55°C with a full rated output up to 40°C.

Bluetooth Smart enabled:
Any Bluetooth enabled smartphone, tablet or other devices can be used to monitor, to change settings, and to update the charger when new software features become available.
 
Fully programmable:
  • Battery charge algorithm (configurable) or fixed output.
  • Smart alternator compatibility: engine running detection mechanism.
 
Adaptive 3-stage charge algorithm bulk – absorption – float:
  • For lead-acid batteries, it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged.
  • For lithium batteries, absorption time is fixed default 2 hours.
  • Alternatively, a fixed output voltage can be chosen.
 
Remote on-off:
A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two-pole connector can be switched to battery minus (or the chassis of a vehicle, for example).
 
All models are short circuit proof and can be paralleled to increase output current:
An unlimited number of units can be connected in parallel.
 
High temperature protected:
The output current will reduce at high ambient temperature.
 
IP43 protection:
When installed with the screw terminals oriented downwards.
 
Screw terminals:
No special tools needed for installation.

Input fuse (not replaceable)

Victron DC-DC Chargers: Non-Isolated vs Isolated:
The main difference with an isolated DC-DC charger is the connection to each battery as there is only one negative connection to the battery. Plus, there is no internal connection between the negatives in the battery. Some systems require an isolated DC to DC charger, this can be some of the reasons:
  • Typically, marine application with limited corrosion
  • Decrease noise from one battery system that will affect another battery system
Either unit can be used for systems that don’t require isolation, but the non-isolated requires one less wire to be installed. 
One example of a non-isolated system is an automotive system, such as both batteries are negative and connected to the chassis of a vehicle. The system is non-isolated but either unit will suit. 
 
No Solar Regulator in the DC-DC Charger:
Victron have chosen to separate the charger and the solar regulators, these are the advantages:
  • You can choose the correct solar regulator to match your panels with the best efficiency for the solar charging
  • The solar can be charging into the battery system simultaneously with the onboard vehicle charging
  • Without a solar regulator, the DC-DC charger will stay cheaper

 

Specifications: 

  • Output Current Rating 30 Amps
  • DC Input Voltage 10-17V 
  • DC Output Voltage 12,2 V
  • Standby Current Less than 1mA
  • Efficiency 87%
  • Operating Temperature Range -20 to +55°C (derate 3% per °C above 40°C)
  • Humidity Maximum 95% non-condensing
  • Short Circuit Current 60A
  • Under Voltage Shutdown 7V
  • Maximum Charge Current 40A
  • No Load Power Consumption <80 mA
  • Dimensions 130 x 186 x 80 mm 
  • Warranty 5 Years

Dometic Harrier Brochures

 

Victron Phoenix Smart IP43 12/30 (1+1) 230V Battery Charger:

With boat owners in mind this adaptive 5-step charger can provide either 30A or 50A of charge to each of three battery banks. Or the Phoenix 1+1 model provides 3A to the starter-battery, the rest to the ‘house’ bank. 24V models are available with 16A/25A charge. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features – see the datasheet below. 

Specifications:

Output Current Rating (Amps)                                               30.0 Amps
Efficiency 94%
Operating Temperature Range -20 to 60°C (0 - 140°F)
AC Input Connection IEC 320 C14 inlet with retainer clip (AC cord with country specific plug must be ordered separately)
Humidity Max 95%
Charge current 30 A
Dimensions (LxWxH) mm 180 mm x 249 mm x 100 mm (LxWxD)
Net Weight (kg) 3.5 Kg
Charge Algorithm 5 stage adaptive
Charge voltage 'absorption' Normal: 14,4V High: 14,7V Li-ion: 14,2V
Charge Voltage Float - Wet (25 degrees)** Normal: 13,8V High: 13,8V Li-ion: 13,5V
Charge voltage 'storage' Normal: 13,2V High: 13,2V Li-ion: 13,5V
Protection category IP43 (electronic components), IP22 (connection area)
Battery-connection Screw terminals 16 mm² (AWG6)
Input Voltage 230 VAC (range: 210 – 250 V
Manufacturers Warranty 5 Years

 

Features:

Bluetooth Smart enabled
Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.

Phoenix Smart (1+1): two outputs to charge 2 battery banks
The second output, limited to approximately 3A and with a slightly lower output voltage, is intended to top up a starter battery.

Phoenix Smart (3): three full current outputs to charge 3 battery banks
Each output can supply the full rated output current. But the total of the 3 outputs combined can never exceed the current rating of the charger.

Automatic voltage compensation
The charger compensates for voltage drop over the DC cabling by slightly increasing output voltage when the DC current increases. Please see the manual for details.

Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage
The Phoenix Smart Charger features our well-known ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimise the charge process relative to the way the battery is being used.

The right amount of charge: variable absorption time
When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery will be fully charged.

Preventing damage due to excessive gassing: the BatterySafe mode 
If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached 

Less maintenance and aging when the battery is not in use: the Storage Mode
The Storage Mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage Mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.

Also charges Li-ion (LiFePO₄) batteries
Charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-ion BMS to the remote on-off port.
Alternatively full control of voltage and current can be achieved with Bluetooth.

Fully programmable charge algorithm
The charge algorithm can be programmed with help of Bluetooth or the VE.Direct interface.
Three preprogrammed algorithms can be selected with the mode button (see specifications).

Remote on-off
The remote on/off consists of two terminals: Remote H and Remote L.
A remote on/off switch or relay contact can be connected between H and L.
Alternatively, terminal H can be pulled high, or terminal L can be pulled low.
See manual for details.

VE.Direct interface
For a wired data connection to a Color Control panel, PC or other devices.
Please see the VictronConnect app under Downloads / Software on our website.

Programmable relay
Can be programmed using the VE.Direct interface or a Bluetooth enabled device
to trip on an alarm or other events.

Dometic Harrier Brochures

Dometic Harrier Operation Manual

 

Victron Phoenix Smart IP43 Charger Mains Power Cord AU/NZ (2m):

A single spare or replacement Mains Cord to suit the Smart IP43 chargers.

Features:

  •  2 Metres

 

Victron Smart Battery Sense Long Range (up to 10m):

Smart Battery Sense is a wireless battery voltage and temperature sensor for Victron MPPT Solar Chargers.

With voltage and temperature sense in place, batteries will be better charged; improving charging-efficiency and prolonging battery life.

Improves battery charging

By measuring the voltage at the battery bank terminals, errors arising from voltage-loss due to cable resistance are avoided - guaranteeing the correct charge-voltage.

For lead batteries, battery temperature data is used to adjust the charge-voltages: cold batteries require an increased charge-voltage, whereas hot batteries require a decreased charge-voltage. For lithium batteries temperature data is used to disable charging when they are too cold: charging lithium batteries near or below freezing causes permanent damage to the cells.

Look no wires

The connection between Smart Battery Sense and one or more Solar Charger(s) is wireless: It uses VE. Smart Network - a wireless technology based on Bluetooth Smart.

Information transmitted can be used simultaneously by one, two, or more Solar Chargers connected to the same 12V, 24V,  and 48V battery bank. The Smart Network is set up using the VictronConnect app.

Tidy, simple - smart

Installation is simple, quick, and tidy. Just connect the unit's two eyelets to your battery terminals and attach the Smart Battery Sense unit directly onto the battery-body using its self-adhesive strip.

Dometic Harrier Product Diagram

 

Victron SmartSolar MPPT 75/15 Charge Controller:

Solar charge controller:
A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.
 
MPPT: Ultra Fast Maximum Power Point Tracking:
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.
 
Remote Monitoring and Control:
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in Bluetooth by pairing it with your smartphone or other devices via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by Bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.
 
Load output:
The intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery.
 
 
Specifications:
Amps 15.0 Amps
Voltage 12/24V Auto Select
Nominal PV Power 12V - 220W | 24V - 440W
Efficiency 98% (Peak)
Operating Temperature Range -30 to +60°C (full rated output up to 40°C)
Humidity 95%, non-condensing
Dimensions (LxWxH) mm 40 x 113 x 100 (D x W x H)
Net Weight (kg) 0.5 Kg
Charge voltage 'absorption' 14.4V / 28.8V (adjustable)
Protection                                                                                        Battery reverse polarity (fuse), Output short circuit and Over temperature
 
 

 

Victron Battery Monitor BMV-712 Smart: 

With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance.

Specifications:

Supply Voltage Range                                                6,5 - 70 VDC
Current Draw < 1mA
Relay 60V / 1A normally open (function can be inverted)
Operating Range (temp) -40 +50°C (-40 - 120°F)
Battery Capacity 1 - 9999 Ah
Dimensions Front: 63 mm diameter | Front bezel: 69 x 69 mm | Body diameter: 52 mm | Body depth: 31 mm
Temperature Range -20 +50°C
Current ± 0,01A
Voltage ± 0,01V
Amps ± 0,1 Ah (hours)
State of Charge (0-100%) ± 0,1%
Time to go ± 1 min
Accuracy of current measurement ± 0,4%
Accuracy of voltage measurement ± 0,3%
Input Voltage 6,5 - 70 VDC
Installation Flush mount
Safety EN 60335-1
Emission / Immunity EN 55014-1 / EN 55014-2
Battery Automotive ECE R10-4 / EN 50498
NOTE Measure voltage of second battery, temp, or midpoint: Yes | VE.Direct Communication port: Yes
Included Shunt (500A / 50mV), Cable (10 m, 6 core UTP with RJ12 connectors, and cable with fuse for ‘+’ connection)
Manufacturers Warranty 5 Years

 

Features:

  • Battery voltage, current, power, ampere-hours consumed and state of charge
  • Remaining time at the current rate of discharge
  • Programmable visual and audible alarm
  • Programmable relay, to turn off non critical loads or to run a generator when needed
  • 500 Amp quick connect shunt and connection kit
  • Shunt selection capability up to 10.000 Amps
  • VE.Direct communication port
  • Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health
  • Wide input voltage range: 6,5 – 70V
  • High current measurement resolution: 10 mA (0,01A)
  • Additional input to measure voltage (of a second battery), temperature or midpoint voltage, and corresponding alarm and relay settings

Download the Victron Bluetooth app

Use a smartphone or other Bluetooth enabled device to:

  • Customize settings
  • Monitor all important data on single screen
  • View historical data
  • Update the software when new features become available.

Easy to install

All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for rear mounting and screws for front mounting.

Midpoint voltage monitoring

One bad cell or one bad battery can destroy a large, expensive battery bank. When batteries are connected in series, a timely warning can be generated by measuring the midpoint voltage. Please see the BMV manual, section 5.2, for more information.

Very low current draw from the battery Current consumption

0,7Ah per month (1mA) @12V and 0,6Ah per month (0,8mA) @ 24V Especially Li-ion batteries have virtually no capacity left when discharged until low voltage shutdown. After shutdown due to low cell voltage, the capacity reserve of a Li-ion battery is approximately 1Ah per 100Ah battery capacity. The battery will be damaged if the remaining capacity reserve is drawn from the battery. A residual current of 10mA for example may damage a 200Ah battery if the system is left in discharged state during more than 8 days.

Bi-stable alarm relay

Prevents increased current draw in case of an alarm. 

Dometic Harrier Brochures

Dometic Harrier Operation Manual

 

Victron Temperature Sensor for BMV-702/712: 

With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance.

Features:

Bluetooth inside

With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance.

Download the Victron Bluetooth app

Use a smartphone or other Bluetooth enabled device to:

  • customize settings,
  • monitor all important data on single screen,
  • view historical data, and to
  • update the software when new features become available.

 

Easy to install

All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed.
Also included are a separate front bezel for a square or round display appearance, a securing ring for rear mounting and screws for front mounting.

Midpoint voltage monitoring

One bad cell or one bad battery can destroy a large, expensive battery bank. When batteries are connected in series, a timely warning can be generated by measuring the midpoint voltage. Please see the BMV manual, section 5.2, for more information. 
Victron recommend their Battery Balancer (BMS012201000) to maximize service life of series-connected lead-acid batteries.

Very low current draw from the battery

  • Current consumption: 0,7Ah per month (1mA) @12V and 0,6Ah per month (0,8mA) @ 24V Especially Li-ion batteries have virtually no capacity left when discharged until low voltage shutdown.
  • After shutdown due to low cell voltage, the capacity reserve of a Li-ion battery is approximately 1Ah per 100Ah battery capacity. The battery will be damaged if the remaining capacity reserve is drawn from the battery. A residual current of 10mA for example may damage a 200Ah battery if the system is left in discharged state during more than 8 days.

 

Bi-stable alarm relay

Prevents increased current draw in case of an alarm.

Other features:

  • Battery voltage, current, power, ampere-hours consumed and state of charge
  • Remaining time at the current rate of discharge
  • Programmable visual and audible alarm
  • Programmable relay, to turn off non critical loads or to run a generator when needed
  • 500 Amp quick connect shunt and connection kit
  • Shunt selection capability up to 10.000 Amps
  • VE.Direct communication port
  • Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health
  • Wide input voltage range: 6,5 – 70V
  • High current measurement resolution: 10 mA (0,01A)
  • Additional input to measure voltage (of a second battery), temperature or midpoint voltage, and corresponding alarm and relay settings
Dometic Harrier Brochures

Dometic Harrier Operation Manual

 

Victron Smart Battery Protect 12/24V-65A:

The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.

When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled.

Specifications:

  • Maximum continuous load current* - 65A
  • Peak current (during 30 seconds) - 250A 
  • Operating voltage range - 6 –35V
  • Current consumption BLE On   - When on: 1,4 mA When off or low voltage shutdown: 0,9 mA | BLE Off   - When on: 1,2 mA When off or low voltage shutdown: 0,7 mA
  • Alarm output delay - 12 seconds
  • Maximum load on alarm output - 50 mA (short circuit proof)
  • Load disconnect delay - 90 seconds (immediate if triggered by the VE.Bus BMS)
  • Load reconnect delay - 30 seconds
  • Default thresholds - Disengage: 10,5V or 21V Engage: 12V or 24V
  • Operating temperature range - Full load: -40°C to +40°C (up to 60% of nominal load at 50°C)

SKU BDL010

Brand Victron

Product Category Battery Chargers

Voltage 12V

Output Current Rating (Amps): 30 Ah

Weight: 8.5 Kg

Dimensions: 130 x 186 x 80 mm (L x W x H) (DC Charger) | 180 x 249 x 100 mm (L x W x H) (AC Charger) | 40 x 113 x 100 mm (Solar Charge Controller) | Front: 63 mm diameter, Front bezel: 69 x 69 mm, Body diameter: 52 mm, Body depth: 31 mm (Battery Monitor) | 106 x 48 x


NOTE: see full product specifications & further product info in the Description section on this page.

Warranty Period: 5 Years

Warranty Details: Please CLICK HERE for Warranty Information on this product

  • We ship Australia-wide with national road express freight companies such as Star Track, TNT and Toll.
  • Small Items are sent with Australia Post via regular post.
  • Delivery times are generally 3-5 days from day of dispatch for major cities (sometimes quicker). Please allow longer for regional and remote areas.
  • Once your item(s) have been dispatched, we will provide you freight tracking information so you can track your delivery to your door.
  • Items are fully insured during the freight process.
  • Unfortunately we cannot deliver to PO Boxes.
  • For further details on our Delivery Process you can visit our Delivery Page HERE.

Important Covid-19 Comment: during these difficult times, our dispatch and delivery times are longer than normal. Please allow additional days for delivery over and above the normal estimates outlined above.

Be The First To Review This Product!

Help other CARAVANRVCAMPING users shop smarter by writing reviews for products you have purchased.

Write a product review